◀ Previous: 2. The WC Animation Tools Tab · 🏠 WC Animation Tools · Next: 4. Root Motion Steps ▶


Timing steps change when things happen in an animation: cutting it shorter, holding a pose, speeding it up, changing its frame rate, or making it loop. They always run first, before any other kind of step.

You add every step the same way:

  1. Open the animation and click the WC Animation Tools tab.
  2. Click Add Operation and pick the step.
  3. Change its settings (they show under the step).
  4. Tick Preview to watch the result.
  5. Click Apply when you're happy, then save.

<aside> ℹ️

Not sure what Start, End or Ease mean? They're explained once on 2. The WC Animation Tools Tab, under Settings many steps share. Quick version: times are in seconds, and an End of -1 means the end of the animation.

</aside>

Trim

Keeps one part of the animation and cuts the rest.

Use it when a clip has extra frames at the start or end, like a pause before an attack.

Setting What it does
Keep > Start The second the kept part starts.
Keep > End The second the kept part ends (-1 = the end).

Good to know:

Example: a 2-second sword swing has half a second of standing still at the start. Set Start to 0.5 and leave End at -1. The new clip is 1.5 seconds long and starts right on the swing.

Hold Frames

Freezes the pose at a moment for a while. The animation gets longer by every hold.

Use it to add weight to a pose, like holding the top of a big overhead swing.

  1. Under Holds, click the + to add a hold.
  2. Set At: the second where the pose is held.
  3. Set Hold For: how many seconds it's held (default 0.2).
  4. Add more holds the same way if you need them.

Good to know: everything after a hold (notifies, sync markers and curves) moves later by the hold's length, so it all stays in step with the motion.

Time Warp

Plays parts of the animation faster or slower, following a speed curve you draw.

Use it to make an attack wind up slowly and then strike fast, without changing the whole clip.

Setting What it does
Speed A curve. Across (left to right) is the original animation: 0 = its start, 1 = its end. Up is the speed: 1 = normal, 2 = twice as fast, 0.5 = half speed. Speeds are kept between 0.05 and 20.
Keep Length Ticked: the clip stays the same total length, and the curve only shapes where it's fast or slow. Unticked: a faster clip gets shorter, a slower one longer.

How to draw the curve:

  1. The curve starts as a flat line at 1 (normal speed).
  2. To add a point, hold Shift and click on the curve box, or right-click in it and choose Add key.
  3. Drag a point up to speed that moment up, or down to slow it.

Example: to make the first half slow and the second half fast, add a point at across 0 with speed 0.6, and another at across 1 with speed 1.6. Tick Keep Length so the clip stays the same length.

Resample

Changes the frame rate. The poses are sampled again at the new rate.

Use it when clips in one project were made at different frame rates and you want them all the same.

Setting What it does
Target Rate The new frame rate. Any rate works, including 23.976, 25 and 48. Default 30.

<aside> 💡

The Audit tab can find clips whose frame rate doesn't match the rest of their folder and add this step for you.

</aside>

Make Loop

Makes part of the animation loop smoothly: its end flows back into its start without a pop or freeze.

Use it on idles, walks and runs that jump when they repeat.

Setting What it does
Loop Range The part that becomes the loop (Start and End in seconds).
Blend Time How many seconds the end blends into the start. Default 0.25. It can be at most half the loop's length.
Blend Ease How the blend fades (see Ease on page 2). Default Smooth Step.
Blend Root As Velocity Ticked (default): the character keeps moving through the join, so a walking loop doesn't stop or jump. Untick it only for clips that stay in place.

Example: an idle has a small hitch when it repeats. Add Make Loop, leave Loop Range as the whole clip, set Blend Time to 0.3, and preview. The hitch is gone.

Reverse (WC Animation Maker only)

Plays the animation backwards: bone keys, curves, attributes, notifies and sync markers.

Because reversing makes a second animation you'd keep next to the original, Reverse lives in the WC Animation Maker's Steps, not in this tab. See 6. WC Animation Maker.

Setting What it does
Start Root At Origin Ticked (default): the reversed root starts at the character's feet, so a reversed walk doesn't start metres away.

Mirror (WC Animation Maker only)

Flips the animation left to right. It also lives in the Maker's Steps. Its settings are on 6. WC Animation Maker.


◀ Previous: 2. The WC Animation Tools Tab · 🏠 WC Animation Tools · Next: 4. Root Motion Steps ▶