◀ Previous: 3. Timing Steps · 🏠 WC Animation Tools · Next: 5. Bone and Pose Steps ▶
Root motion steps change where the character goes. They work on the root (the top bone, which moves the character in the game when root motion is on) and the pelvis (the hips, which carry the body).
<aside> 🧠
Root motion in one sentence: if an animation's travel is in the root bone and Enable Root Motion is ticked in the animation's Asset Details, the game moves the character by exactly what the animation does. If the travel is in the hips instead, the body walks away from the character's capsule. Most of these steps move travel between the two.
</aside>
Add them like any step: WC Animation Tools tab > Add Operation > pick the step > change its settings > tick Preview > Apply.
While you preview, the viewport shows the root's path before (grey line) and after (yellow line). That's the easiest way to see what a root step did.
Moves the body's travel and turning into the root. The body keeps its pose.
Use it on clips where the hips walk forward but the root stays still (common in downloaded animations). After this step the root carries the travel, so root motion works in game.
| Setting | What it does | Default |
|---|---|---|
| From | The bone whose travel goes into the root. Leave it as None to use the hips from your Bone Profile. | None |
| X | Take the travel along the mesh's X axis. | On |
| Y | Take the travel along the mesh's Y axis. | On |
| Z | Take the height too. Turn it on for jumps and climbs. | Off |
| Yaw | Take the turning too. | On |
| Yaw Source | Where the turn comes from: Bone Facing (the way the hips face) or Travel Direction (the way the hips move). | Bone Facing |
| Start At Origin | Start the root at the character's feet, facing ahead, on the first frame. | On |
| Smoothing | Smooths the root's path over this many seconds, taking out the hips' bob and sway. 0 = off. Try 0.2 to 0.4 for walks. | 0 |
Step by step, a walk whose hips travel:
The opposite of Extract. The root goes back to the character's feet and stays there, and the body keeps travelling.
Use it when you need the travel in the hips, for example for a system that moves the character itself.
| Setting | What it does | Default |
|---|---|---|
| Keep Root Rotation | Keep the root's turning. Only its travel moves into the body. | Off |
Takes the travel out, so the character stays on the spot.
Use it to turn a forward walk into a walk on the spot (for a treadmill, or for code that moves the character).
| Setting | What it does | Default |
|---|---|---|
| From Root | Take the travel out of the root (the body moves back with it). | On |
| From Pelvis | Hold the hips over where they start. Turn this on for clips whose travel is in the hips. | Off |
| Keep Height | Keep the root's height, so jumps still go up. | On |
| Keep Turning | Keep the root's turning. | On |
<aside> 💡
This step also works in the WC Animation Maker's Steps.
</aside>
Moves and turns the root by a fixed amount, or starts it at the character's feet.
| Setting | What it does | Default |
|---|---|---|
| Mode | Add Offset: move and turn the root by a fixed amount. Start At Origin: take the first frame's ground position and turn off every frame, so the clip starts at the feet, facing ahead. | Add Offset |
| Move | (Add Offset only) How far to move the root, in cm, in the root's own directions. | 0, 0, 0 |
| Turn | (Add Offset only) How far to turn the root, in degrees. | 0 |
| Keep Body In Place | Ticked: only the root moves; the body stays where it was. Unticked: the body moves with the root. | Off |
| Reset Root Scale | Set the root's scale to 1 on every frame. Fixes clips that shrink or grow the character. | Off |
Example: a clip starts with the character 50 cm to the left of where it should be. Set Mode to Start At Origin and apply.
Turns the travel to a new direction, spreading the turn over the distance walked, while holding planted feet still.
Use it when a walk drifts off to one side, or to make a 45-degree walk from a straight one.
Direction
| Setting | What it does | Default |
|---|---|---|
| Target | Which way to travel. Facing: the way the character faces on the first frame (fixes drift). Angle From Facing: the facing turned by Angle. World Angle: Angle measured from the mesh's own forward direction. | Facing |
| Angle | Degrees, for the two Angle targets. | 0 |
| Turn Clockwise At 180 | For an exact 180-degree turn only: ticked turns clockwise (seen from above), unticked turns anticlockwise. | On |
Spread
| Setting | What it does | Default |
|---|---|---|
| Gradual | Ticked: the turn is spread over the distance walked. Unticked: the whole clip turns at once. | On |
| Balance | -1 turns early, 1 turns late, 0 evenly. | 0 |
| Window | The turn only happens inside this part of the clip (the whole clip by default). | Whole clip |
| Pivots | Instead of spreading by distance, turn in stretches of time you choose. Each pivot has a Range, a Share of the turn (shares are scaled to add up to the whole turn) and an Ease. Leave it empty to spread by distance. | Empty |
Facing
| Setting | What it does | Default |
|---|---|---|
| Facing | Turn With Travel: the body turns with the new direction. Keep Facing: the body keeps facing the way it did, so the character strafes. | Turn With Travel |
Feet
| Setting | What it does | Default |
|---|---|---|
| Lock Feet | Hold planted feet still while the path turns, so they don't slide. | On |
| Feet | How planted feet are found. See How planted feet are found below. | |
| Max Correction | How fast the foot lock may move the body, in cm per second. | 60 |
Example, a walk that drifts right: add Fix Direction, leave Target on Facing, preview. The yellow line now runs straight ahead.
Stops feet from sliding. It finds where each foot is planted and holds it still, moving the body a little to make up the difference.
| Setting | What it does | Default |
|---|---|---|
| Feet | How planted feet are found. See below. | |
| Max Correction | How fast the lock may move the body, in cm per second. Higher fixes bigger slides but can make the body jerk. | 60 |
While you preview, planted feet show as green dots (left) and blue dots (right). If a foot that should be planted has no dots, change the Feet settings below.
<aside> 💡
The Audit tab measures how far feet slide in a whole folder and can add Lock Feet to every clip that needs it.
</aside>
A foot counts as planted when it's low, not lifting or landing, and not swinging past. It's found by contact, not by speed, so a foot that slides is still found (and can then be held still).
| --- | --- | --- |
If feet aren't found: raise Plant Height a little (try 5). If swinging feet are found by mistake: lower Plant Speed (try 60).
◀ Previous: 3. Timing Steps · 🏠 WC Animation Tools · Next: 5. Bone and Pose Steps ▶