◀ Previous: 4. Root Motion Steps · 🏠 WC Animation Tools · Next: 6. WC Animation Maker ▶


These steps change individual bones: snapping IK bones into place, moving motion from one bone to another, nudging bones, and putting saved hand poses on the fingers.

Add them like any step: WC Animation Tools tab > Add Operation > pick the step > change its settings > tick Preview > Apply.

<aside> 🛡️

Weapons and props are protected. Any bone listed under Weapon Bones in your Bone Profile is never written by a pose step.

</aside>

Snap Bones

Puts bones exactly where other bones are. Its main job: putting the IK bones (like ik_foot_l and ik_hand_r) on the real feet and hands. Many downloaded animations have IK bones that don't move, which breaks foot and hand IK in game.

Snap Bones always runs last, after every other step, so the IK bones match the final pose.

Setting What it does Default
Use Profile Pairs Snap the pairs listed in your Bone Profile (for example ik_foot_l onto foot_l). On
Extra Pairs More pairs, snapped after the profile's. Each pair has Follow (the bone to follow) and Write (the bone that's moved onto it). Empty
Offset Mode None: the bone goes exactly where its Follow bone is. Keep First Frame: the gap between them on the first frame is kept. Custom: a gap you type in Custom Offset. None
Custom Offset (Custom only) The gap from the Follow bone, in its own space.
Position Snap the position. On
Rotation Snap the rotation. On
Weight How far toward the Follow bone, 0 to 1. 1 = all the way. 1
Range The part of the animation that's snapped. Whole clip

Step by step, fix IK bones that don't move:

  1. Add Snap Bones. Leave the defaults.
  2. Tick Preview. White lines join each pair in the viewport. They should be very short (the bones sit on top of each other).
  3. Click Apply and save.

Transfer Motion

Moves motion from one bone to another, on the axes you choose. For example, the hips' travel into the root.

Setting What it does Default
From The bone whose motion moves. None = the hips from your Bone Profile. It must sit somewhere under To in the skeleton. None
To The bone that takes the motion. None = the root from your Bone Profile. None
X, Y, Z Which directions to move (along the mesh's axes; Z is height). X and Y on, Z off
Yaw Move the turning too. On
Keep From Still Ticked: From stops moving because To now carries the motion. Unticked: From keeps its own motion as well. On
Children Keep Pose Ticked: To's other children stay where they were. Unticked: they ride along with To. On

<aside> 💡

For the common case (hips' travel into the root) Extract Root Motion on page 4 has more options, like smoothing. Use Transfer Motion for any other pair of bones.

</aside>

Bone Offset

Moves and turns chosen bones over part of the animation, fading in and out.

Use it to fix a hand that goes through a hip, raise a weapon a little, or tilt the head.

Setting What it does Default
Bones The bones to change. Click + and pick each one. Empty
Move How far to move them, in cm. 0, 0, 0
Turn How far to turn them, in degrees (Roll, Pitch, Yaw). 0, 0, 0
Space Which axes the move and turn use. Bone: the bone's own axes (like the local gizmo in the Animation Editor). Parent: the parent bone's axes. Component: the whole mesh's axes. Bone
Range The part of the animation that changes. Whole clip
Blend In Seconds the change takes to fade in at the start of the range. 0
Blend Out Seconds the change takes to fade out at the end of the range. 0
Ease How the fades curve. Linear
Children Keep Pose Ticked: the bones' children stay where they were. Unticked: they ride along. Off

Example, the right hand clips through the hip between 0.4 s and 0.9 s:

  1. Add Bone Offset.
  2. Under Bones, add hand_r.
  3. Set Space to Component and Move to 0, 0, 4 (4 cm up).
  4. Set Range Start to 0.4 and End to 0.9.
  5. Set Blend In and Blend Out to 0.1 so it eases in and out.
  6. Preview, then Apply.

Hand Pose

Puts a saved finger pose on a hand over part of the animation. Only the finger bones are written, never the hand bone or a weapon bone. Because only rotations are saved, each mesh keeps its own finger lengths.

First you need a Hand Pose Library with at least one pose in it. See Saving hand poses below.

Setting What it does Default
Library The Hand Pose Library the pose comes from. Empty
Pose Name The pose. The drop-down lists the library's poses.
Hand Left, Right or Both. Right
Range The part of the animation that's posed. Whole clip
Blend In Seconds the pose takes to fade in. 0.1
Blend Out Seconds the pose takes to fade out. 0.1
Ease How the fades curve. Ease In Out
Weight How much of the pose, 0 to 1. 1

Saving hand poses

Make a Hand Pose Library (once)

  1. In the Content Browser, click Add.
  2. Go to Animation > WC Animation Tools > Hand Pose Library.
  3. Name it, for example HPL_Hands.

It starts empty. You fill it by capturing poses.

Capture a pose

  1. Open an animation where the hand is in the pose you want (for example a fist, or gripping a sword).
  2. Scrub the timeline to the exact frame.
  3. In the WC Animation Tools tab, find the Capture Hand Pose section.
  4. Pick your Hand Pose Library in the box.
  5. Choose Left, Right or Both.
  6. Type a Pose name, for example Fist.
  7. Click Capture.
  8. The result line says something like Captured "Fist" (Right hand) at 0.53 s into HPL_Hands. Save the library.

<aside> ⚠️

Capturing a pose with a name that already exists replaces it.

</aside>

<aside> ℹ️

Capture reads the finger bones from your Bone Profile (Left Fingers and Right Fingers). If it says The Bone Profile names no finger bones this mesh has for that hand, open the Bone Profile and fill in the finger bones.

</aside>


◀ Previous: 4. Root Motion Steps · 🏠 WC Animation Tools · Next: 6. WC Animation Maker ▶